Troubleshooting a Water Heater Emergency: What to Do When It Stops Working

Troubleshooting a Water Heater Emergency: What to Do When It Stops Working

Blog Article


The article listed below on the subject of How to Troubleshoot and Repair an Electric Water Heater is immensely enjoyable. Read on and make your own conclusions.

Hot Water Heater Repair
Numerous contemporary houses use an electrical hot water heater for their heater, because of its comfort and also convenience of use. Nonetheless, similar to any other electric devices, issues might develop with its usage, suddenly. It can be really discouraging to get up to a chilly shower instead of a hot one or having your bath with water that isn't warm adequate and even as well hot. Whatever the case may be, water heater troubles can be fairly nerve-racking. Fortunately, we've made a list of possible services to your water heater concerns. There are a variety of factors that could cause a lot of these problems, it could be an issue with the power supply, the electrical heating element, or the thermostat. Prior to doing anything, ensure you shut off the primary power supply for security. Whatever the issue is, getting it repaired ought to not position too much of an issue if you follow these actions:

Call An Expert:

If after replacing all defective parts and resetting your temperature level, the hot water heater still isn't functioning, you may need to contact an expert plumber for a specialist viewpoint. The problem with your heater could be that the cold and hot faucets have been switched or it may be undersized for the quantity of warm water needed in your house. Whatever the situation may be, a professional plumber would certainly assist resolve the problem.

Examine Your Power Supply:

As fundamental as this may seem, it is extremely required. Without adequate power, your hot water heater will not function. So the first thing to do when your water instantly retires is to verify that it isn't a power problem. Examine if the fuse is burnt out or the breaker tripped. If the breaker is the problem, simply transform it on and off again. Change any type of broken or worn-out fuse. Test the home appliance with power after these changes to see if it's currently functioning.

Check Your Thermostat:

If your hot water heater still isn't working or the water appearing isn't hot sufficient, you may require to check the temperature level settings on your top thermostat. Guarantee the circuit breaker is turned off before doing anything. Open up the access panel and press the red switch for temperature reset over the thermostat. This ought to aid heat up the water. Transform the circuit breaker back on and also inspect if the trouble has actually been fixed.

Check the Burner in the Hot Water Heater:

If it's not a power issue, after that try looking into your heating element if it is still functioning. Test each of your burner to make sure the trouble isn't with any one of them. If any of them is defective, replace that part and after that check whether the warm water is back on.


Water heater troubles are not constantly significant. Most of them are because of minor concerns like a blown fuse or worn-out burner. Changing the defective parts need to suffice. Nonetheless, if you are still incapable to fix the issue, give a call to your closest plumber to come to get it fixed.

8 possible reasons why you have no Hot Water

Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.

Water Leak

Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.

Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.

Gas Heater: Gas Leak

If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.

Gas Heater: Pilot Light Problems

There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.

Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.

Gas Heater: Faulty Thermocouple

The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.

Electric Heater: Breaker Blues

Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.

Electric Heater: Reaching The Limit

If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.

Electric Heater: Heating Element

If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

No Hot Water — Water Heater Repair

As a fervent person who reads on How to Troubleshoot and Repair an Electric Water Heater, I imagined sharing that editorial was essential. Liked our blog? Please share it. Help someone else locate it. I thank you for reading our article about How to Troubleshoot and Repair an Electric Water Heater.

24/7 plumbers for emergencies.

Report this page